Dell 5324 Switch
From Nonecks Docs
- Notes & Links
Contents |
To Update Firmware and Boot Images for Dell 5324 Switches:
- Files are located on TFTP server @ (10.10.10.5)
- Dell 5324 Updated System Image: 5324-2013.ros
- Dell 5324 Updated Boot Image: 5324-boot-10202.rfb
Login to Switch by Console and switch to enable mode
Configure IP to one port of switch so file transfers can Occur
console# configure console(config)# interface ethernet g24 console(config-if)# ip address 10.1.253 255.255.255.0 console(config-if)# exit
Copy the Boot image and System image from tftp to the device
console# copy tftp://10.10.10.5/5324-boot-10202.rfb boot !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!! Copy: 524304 bytes copied in 00:00:16 [hh:mm:ss]
console# copy tftp://10.10.10.5/5324-2013.ros image !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Copy: 3448112 bytes copied in 00:01:54 [hh:mm:ss] console# reload
Copy Configuration from TFTP Server
console# copy tftp://10.10.10.5/name-of-switch.cfg running-config 23-Jul-2009 12:16:40 %COPY-W-TRAP: The copy operation was completed successfully Copy succeeded chi-sw3# copy run start chi-sw3# reload
Manually Configure Device
Configuring an Initial Terminal Password
- To configure an initial terminal password, enter the following commands:
console# configure console(config)# aaa authentication login default line console(config)# aaa authentication enable default line console(config)# line console console(config-line)# login authentication default console(config-line)# enable authentication default console(config-line)# password george console(config)# exit
Configuring an Initial SSH Password
- To configure an initial SSH password, enter the following commands:
console# configure console(config)# aaa authentication login default line console(config)# aaa authentication enable default line console(config)# line ssh console(config-line)# login authentication default console(config-line)# enable authentication default console(config-line)# password jones. console(config-line)# exit console(config)# ip ssh server console(config)# exit
Configuring an Initial HTTPS Password
- To configure an initial HTTPS password, enter the following commands:
console# configure console(config)# ip https authentication local console(config)# username admin password user1 level 15 console(config)# exit
- Enter the following commands once when configuring to use a terminal, a Telnet, or an SSH session in order to use an HTTPS session.
- NOTE: In the Web browser enable SSL 2.0 or greater for the page content to be displayed.
console# configure console(config)# crypto key generate rsa console(config)# crypto key generate dsa console(config)# ip https server console(config)# exit
- Now you should be able to browse to https://ip.of.switch
=== Enable Broadcast Storm Protection on all ports
console# configure console(config)# interface range ethernet g(1,24) console(config)# port storm-control broadcast enable console(config)# exit
Write Running Config to Startup Config
console# copy run start
Copy Startup Config to TFTP Server
console# copy flash://startup-config tftp://10.10.10.5/chi-sw1.cfg